top of page
CE815 Header Wide.jpg
Concrete Texture

About FasTrac CE815 Epoxy Grout

FasTrac CE815 Epoxy Grout is a three-component, 100% solids, high-performance, epoxy machine grout. It is characterized by low dust, high bearing area, low exotherm, negligible shrinkage and creep, fast cure, and excellent flowability.
CE815 Epoxy Grout - New Bags_1x1_Clean_edited.jpg
FasTrac CE815 Epoxy Grout is ideal for high-stress applications such as wind turbines, gas transmission, refining, chemical processing, pulp and paper, crane rail, marine, and other machine base plate grouting. New equipment installations or re-grouting applications subject to chemical attack and extreme vibration are ideal for CE815 Epoxy Grout. CE815 can also be used as an anchoring adhesive.

How does FasTrac CE815 Compare to the Competition?

Energy Tech Systems Epoxy Grout Test Results.jpg

Each epoxy grout was tested using the following ASTM Standards:


  • ASTM C1339

  • ASTM C579 Method B, Load Rate II

  • ASTM D2471


A sample of each epoxy grout was mixed according to ASTM recommended method at an average material & ambient temperature of 82 degrees Fahrenheit.  The flow box was set at a 2” depth and the epoxy grout mix was then poured into the flow box hopper. After waiting 5-minutes, the flow box gate was lifted, allowing the grout to flow through the trough. As soon as the grout contacted the backplate, the time was recorded. The faster the time, the higher the rate of flow.

The fastest Flow Box Times were achieved by Chockfast Versaflow (10.25), FasTrac CE815 (10.45), and Five Star DP (26.62). The Versaflow and CE815 times are incredibly close! They are off by 0.2sec and within the margin of error. We look forward to running this test again in the future to determine if the results remain the same.


For 3-Day Compressive Strength, the top performers were Masterbuilder 648 (14,106), FasTrac CE815 (13,456), and Chockfast Red (13,245).


For 7-Day Compressive Strength, the top performers were Masterbuilder 648 (15,629), Five Star DP (14,485), and Chockfast Red (14,200).

FasTrac CE815 put up some impressive numbers. FasTrac CE815 offers the speed of Chockfast Versaflow and the strength of Chockfast Red, at a significantly reduced price. We've just found our new favorite machine grout! If your project requires an epoxy grout with excellent flowability, high early strength, deep pour capable, and a high effective bearing area, then you owe it to yourself to give FasTrac a try. You won't be disappointed.

Still not convinced FasTrac CE815 is right for you?  Check out this Case Study

CE815 Case Study - Scranton, PA

FasTrac CE815 Epoxy Grout was recently used to complete a difficult grout installation on a high-speed gas compressor with < 2” of clearance, surrounded by piping, conduit, and other ancillary equipment. FasTrac CE815 has exceptional flow and extended working time which makes it the perfect grout for low clearance on large footprint equipment < 2”. anchoring adhesive.

The superior flowability of FasTrac CE815 requires less head pressure to move. This allowed the contractor to pump the grout at a lower-than-usual volume and keep the grout within the forms and off the conduit, piping, and ancillary equipment. The extended working time at shallow depths of the CE815 allowed the contractor to pump the grout at a lower volume and have sufficient time to finish the exposed surfaces.
The combination of CE815 Epoxy Grout and a professional grouting contractor turned a difficult environment into a routine grouting project.  Ready to learn more?  Click the link below to read the entire case study, download the technical data sheet, and download the CE815 product flyer.

All TDS and SDS Downloads

FasTrac Construction Products

Full FasTrac
Product Catalogue

bottom of page